Diese Webseite verwendet Cookies. Durch die Nutzung der Webseite stimmst Du der Verwendung von Cookies zu. Datenschutzinformationen [x]

Sie sind nicht angemeldet.

Werbung

Boote kaufen

Windstärken

Windstärkentabelle

Max1947

Matrose

Beiträge: 60

Wohnort: Barzano' (LC) - Italy

Schiffsname: Trekka

Bootstyp: Vela

Heimathafen: Mandello del Lario - Lago di Como - Italy

  • Nachricht senden

221

Donnerstag, 21. Mai 2020, 23:47

Raymarine Seatalk Autopilot Remote Control con Arduino - Nuova versione

Ciao Andreas, everything arrived and I put it together (I didn't believe it, siig!), But I didn't quite understand how to insert _433_ programming ... it gives me the error you see in the picture. Can you help me out? Waiting for the 6-button remote to arrive, I tried it with a 4-button. The first key "a" does nothing, "b" - "c" - "d" turn the red LED on and off. The oled display shows the word "Start" at the beginning and then remains with the four lines ... I hope I have been clear in my exhibition, but perhaps the photos help better. Thanks in advance and good wind!

https://imagizer.imageshack.com/v2/800x600q90/922/HXXz7Z.png

https://imagizer.imageshack.com/v2/800x600q90/923/w36uKV.jpg

88markus88

Salzbuckel

Beiträge: 3 724

Wohnort: Frankfurt

Schiffsname: Arvika

Bootstyp: Comfortina 35

Heimathafen: Dintelmond

Im Marktplatz: 1

  • Nachricht senden

222

Freitag, 22. Mai 2020, 16:34

Ciao Andreas, everything arrived and I put it together (I didn't believe it, siig!), But I didn't quite understand how to insert _433_ programming ... it gives me the error you see in the picture. Can you help me out? Waiting for the 6-button remote to arrive, I tried it with a 4-button. The first key "a" does nothing, "b" - "c" - "d" turn the red LED on and off. The oled display shows the word "Start" at the beginning and then remains with the four lines ... I hope I have been clear in my exhibition, but perhaps the photos help better. Thanks in advance and good wind!

https://imagizer.imageshack.com/v2/800x600q90/922/HXXz7Z.png

https://imagizer.imageshack.com/v2/800x600q90/923/w36uKV.jpg

@Max1947: Try replacing the / in the faulty line with // and compile again.

Also, you should change the predefined codes in the 4 lines with Key1 to Key4 to values of your own choice. E.g. 0000001 to 1234501, 0000002 to 1234502 and so on. They must be different, though.

Homberger

Admiral

  • »Homberger« ist der Autor dieses Themas

Beiträge: 934

Wohnort: Ratingen

Bootstyp: Bavaria 30 Cruiser

Heimathafen: Buyshaven

Rufzeichen: PE3215

MMSI: 244010500

  • Nachricht senden

223

Samstag, 23. Mai 2020, 13:33

But I didn't quite understand how to insert _433_ programming ...


Hi,

For programming you should use the updated programming code (_433_Programming_New).

https://github.com/AK-Homberger/Seatalk-…Remote-Software

That gives you mor control over the process. Then it should work.

Regards,

Andreas
------------
Seatalk Autopilot Fernbedienung und NMEA2000 WiFi Gateway auf GitHub (Link)

Max1947

Matrose

Beiträge: 60

Wohnort: Barzano' (LC) - Italy

Schiffsname: Trekka

Bootstyp: Vela

Heimathafen: Mandello del Lario - Lago di Como - Italy

  • Nachricht senden

224

Samstag, 23. Mai 2020, 23:25

Raymarine Seatalk Autopilot Remote Control con Arduino - Nuova versione »

Eureka! thanks Andreas and thanks @ 88markus88, now I have to try it out on the boat. After the crown quarantine, thunderstorms have arrived. Good wind at all! :)

225

Montag, 25. Mai 2020, 12:57

Arduino IDE and modified hardware serial communication files

Hello everyone,
I'm trying at home with a ST 60 Muti repeater without success. My setup as follows:
Laptop : MacBook Pro Mojave 10.14.6
IDE: 1.8.10 modified hardware serial files (another IDE 1.8.12 also installed with normal hardware serial files)
On a breadboard circuit is place with OLED and 433 Mhz Receiver and KeyFOB
I can see Micro Pro gets keys and responds at OLED, but always getting "collision" and "send error" once the loop started, even with ST data is not connected and 12V connected.
I have asked many questions to Andreas with PM (many thanks) and tested lots of things.

Now I wonder if those modified hardware serial files are operating system & IDE dependent, I can see many people using this with success, so ;
the ones using this at boat, could you please let me know which operating system and IDE version you are using to upload the code to Micro Pro

Thanks in advance,
Regards, Sancan
(sorry for English, can't speak German)

Counter:

Gezählt seit: 4. Februar 2014, 08:39, nur eingeloggte Mitglieder
 Zugriffe:   Hits heute: 1 513   Hits gestern: 3 562   Hits Tagesrekord: 12 076   Hits gesamt: 5 533 645   Hits pro Tag: 2 401,57 
 Seitenaufrufe:   Klicks heute: 10 400   Klicks gestern: 22 423   Klicks Tagesrekord: 154 353   Klicks gesamt: 42 815 200   Klicks pro Tag: 18 581,57 

Kontrollzentrum